This functionality is only available for certain module packages. Info / Copyright

Check Run Messages: 3D mounting layout

Message number

Message text

P026010

Part placement is completely outside the mounting surface

P026011

3D graphic of the part placement collides with <x>

P026012

Part placement collides with restricted placing area

P026013

Part placement collides with restricted drilling area

P026014

Mounting clearances are not observed

P026015

No part assigned to the part placement

P026016

Device exists on the mounting surface without representation in the schematic

P026017

The structure identifier does not correspond to the mounting surface

P026018

The dimensions of the part placement do not correspond to the dimensions of the part

P026019

The part of the part placement is not available in sufficient numbers at the main function / main terminal

P026020

The function definition of the part placement does not suit the part

P026021

The mounting surface and the main function / main terminal have differing mounting sites (describing)

P026023

The length of the part placement is greater than the delivery length of the part

P026024

The layout space name '<x>' exists more than once

P026025

The part placement does not lie on the mounting rail

P026026

A measuring point is not in the same model view / unfold

P026027

Cut-out is not completely on a mounting surface

P026028

Part placement lies completely within a cut-out.

P026029

The part placement does not have a valid drilling pattern

P026030

Missing NC record for user-defined outline

P026033

Bundle distributed in several bundle groups

P026034

NC mounting surface without valid field size

P026036

Part placement lies in a routing range

P026037

Routing paths lie over each other

P026038

Routing path network no longer up-to-date

P026039

Connection runs through invalid routing paths

P026040

Connection / Cable without valid diameter (<x>)

P026041

Source / Target are placed in different layout spaces

P026042

No entry point to routing path network found

P026043

No routing track between source and target found. <x>

P026044

No connection point pattern defined.

P026045

Routing connection does not end graphically at the targets

P026052

Source / Target is not placed

P026053

Connection point '<x>' does not exist and cannot be created

P026054

Connections of the cable are not defined uniquely

P026055

Connection point '<x>' exists more than once

P026056

Connection cross-section is larger than specified in the connection point pattern

P026057

Connection cross-section is smaller than specified in the connection point pattern

P026058

Number of connections at the connection point <x> is larger than specified in the connection point pattern

P026062

The multi-line connection was not routed

P026070

Bent busbar with invalid total length

P026071

Missing tool at export (copper NC). <x>

P026072

No wire fabrication: <x>

P026073

Routing connection without part number, color / number and/or cross-section / diameter

P026074

NC Export: <x>

P026075

Bending radius of the routing connection is too small

P026076

Cable / tubing protection or cable / tubing tie is not located on a routing path / curve

P026077

Bundle diameter too great; connections cannot be bundled with the selected part

P026078

Bundle diameter too small; connections cannot be bundled with the selected part

P026079

Export Rittal - Athex: <x>

P026080

Could not create export data

P026081

Error while placing a fitting: <x>

P026089

The routing connection <x> collides with <y>

P026090

The actual power dissipation could not be calculated due to missing values

P026091

Incomplete project properties for the air-conditioning calculation

P026092

New air-conditioning calculation required for air-conditioning field <x>

P026093

Missing environmental conditions for air-conditioning calculation at the enclosure

P026094

The numbers of the air-conditioning fields must be unique in the project

P026095

At least two cut-outs overlap completely or partially

P026096

The additional length of the fitting is equal to 0

P026097

The part placement lies outside the optimum air-conditioned area

P026098

The part placement collides with the airflow-specific reserved area

P026099

Unequal power dissipation layout in the air-conditioning field <x> (Power dissipation center: <y>)

P026100

Updating of the part placement is not possible: <x>

P026101

Automatic wiring not possible: <x>

P026102

The <x> part cannot be migrated.

P026103

P026104

The <x> part has not been migrated yet.

See also