Cause
Possibility 1
Not all the connection points on a net were connected to one another.
Example:A net N1 in the schematic apparently connects 5 fuses (-F1 to -F5) with the potential L1.
The net properties show, however, that connection point -F5:1 within the daisy chain is not connected.
Daisy chain
|
Connection point |
Source |
Target |
|---|---|---|
|
L1 |
L1 |
-F1:1 |
|
-F1:1 |
-F1:1 |
-F2:1 |
|
-F2:1 |
-F2:1 |
-F3:1 |
|
-F3:1 |
-F3:1 |
-F4:1 |
|
-F4:1 |
|
|
Possibility 2
Two daisy chains of a net are not connected to one another.
A net N1 in the schematic apparently connects 5 fuses (-F1 to -F5) with the potential L1.
The net properties show, however, that the connection points are in two separate daisy chains:
Daisy chain 1
|
Connection point |
Source |
Target |
|---|---|---|
|
-F4:1 |
-F4:1 |
-F3:1 |
|
-F3:1 |
-F3:1 |
-F2:1 |
|
-F2:1 |
-F2:1 |
-F1:1 |
|
-F1:1 |
Daisy chain 2
|
Connection point |
Source |
Target |
|---|---|---|
|
L1 |
L1 |
-F5:1 |
|
-F5:1 |
|
|
If the connection points on the net were replaced by connectors with target specification, the picture would be as follows:
Possibility 3
A connection was deleted within a net in the schematic. This creates a gap in the daisy chain. In this case, message P005047: Net definition point contains incomplete connections is also output.
Possibility 4
An additional connection that has not yet been assigned to a daisy chain was placed within a net in the schematic by copying. In this case, message P005050: Duplicate ID for net-based connections within a net (<x>) is also output.
Solution
Regarding option 1
For the example under "Possibility 1", the steps are as follows:
- Locate the relevant net definition point in the schematic using the Go to (graphic) function from the popup menu in the Message management dialog.
- Open the Properties <...> dialog for net definition point N1.
- Bring the Net connections tab to the front.
- In the Connection points table, double-click connection point -F5:1.
Connection point -F5:1 is copied to the Connections table and entered beneath the horizontal line of the first daisy chain. This starts a new daisy chain. - Select connection point -F5:1 beneath the horizontal line, then click the
(Move up) button to move it to the daisy chain already ended. - Click [OK] to close the Properties <...> dialog for the net definition point, then start a new project check.
Regarding option 2
Connect the two separated daisy chains.
For the example under "Possibility 2", the steps are as follows:
- Locate the relevant net definition point in the schematic using the Go to (graphic) function from the popup menu in the Message management dialog.
- Open the Properties <...> dialog for net definition point N1.
- Bring the Net connections tab to the front.
- In the Connection points table, double-click connection point -F4:1. Connection point -F4:1 is copied to the Connections table and entered beneath the horizontal line of the second daisy chain. This creates a new daisy chain.
- Click
(End daisy chain) to complete the daisy chain. A horizontal line is created beneath connection point -F4:1 in the Connections table. - Select connection point -F4:1 in the third daisy chain, then click the (Move up) button to move it to the second daisy chain. This breaks up the third daisy chain and connects connection point -F5:1 to connection point -F4:1.
- Click [OK] to close the Properties <...> dialog for the net definition point, then start a new project check.
Regarding option 3
You will find a detailed description in the Help under P005047: Net definition point contains incomplete connections.
Regarding option 4
You will find a detailed description in the Help under P005050: Duplicate ID for net-based connections within a net <x>.
Note:
EPLAN provides the possibility to automatically connect associated distributed terminals (menu items Options > Settings > Projects > "Project name" > Devices > Terminals > Settings (distributed terminals)), even if no drawn connections between the distributed terminals exist. However, this functionality is only effective if a net definition point determines the connections. At least one of the distributed terminal connection points occurring several times in the net so that the message "P005046: Incomplete net" is not output during configuring with distributed terminals.